欧美性爽xxxzzzzzzzz,午夜AV福利老牛,久久99色,国产碰碰福利

網站公告-NOTICE
航豐實業·產品分類
聯系我們
濟南航豐實業有限公司

電話:15168870138
聯系人:龐經理

網址:http://  

廠址: 德州市禹城市莒鎮產業園26棟

經銷商地址:天橋區建華五金市場東區5-1  

魯ICP備09095923號-1

新聞資訊

當前位置:首頁 / 新聞資訊

電纜橋架的支吊架安裝有什么值得注意的?

安裝電纜橋架,應該安裝好電纜橋架的支吊架才可以!但是你知道怎么安裝電纜橋架的支吊架嗎?下面濟南電纜橋架的小編就給大家分析一下支吊架安裝的一些注意事項!
Installation of cable bridge, first of all, should install the cable bridge support hanger can! But do you know how to install the suspension bracket of cable bridge? Next, the small edition of Jinan Cable Bridge Frame will give you an analysis of some matters needing attention in the installation of the suspension frame!
1、架與吊架所用鋼材應平直,無顯著扭曲。下料后長短偏差應在3mm范圍內,切口處應無卷邊、毛刺。
1. The steel used for the frame and hanger shall be straight without significant distortion. The length deviation should be within 3 mm after cutting, and the incision should be free of crimping and burrs.
2、支架與吊架應焊接牢固,無顯著變形,焊接前厚度超過4mm的支架、鐵件應打坡口,焊縫均勻平整,焊縫長度應符合要求,不得出現裂紋、咬邊、氣孔、凹陷、漏焊等缺陷。
2. The bracket and hanger should be welded firmly without significant deformation. Before welding, the bracket and iron parts with a thickness of more than 4 mm should be grooved. The weld seam should be uniform and smooth. The length of the weld seam should meet the requirements. No cracks, undercutting, gas holes, sags and leakage of welding should occur.
3、架與吊架應安裝牢固,保證橫平豎直,在有坡度的建筑物上安裝支架與吊架應與建筑物的坡度、角度一致.
3. The brackets and hangers should be installed firmly to ensure horizontal and vertical. The brackets and hangers should be installed on buildings with slopes in accordance with the slopes and angles of the buildings.
濟南電纜橋架
4、吊具應采用定型產品,并應有各自獨立的吊裝卡具或支撐系統。
4. Lifting fixtures shall adopt stereotyped products and shall have their own independent lifting fixtures or supporting systems.
5、定支點間距一般不應大于1. 5-2m。在進出接線盒、箱、柜、轉角、轉彎和變形縫兩端及丁字接頭的三端500mm以?xún)?nèi)應設固定支持點.
5. Fixed fulcrum spacing should not be greater than 1.5-2m in general. Fixed support points shall be provided within 500 mm at the ends of outlet junction box, box, cabinet, corner, turning and deformation seam and three ends of T-joint.
6、禁用木磚固定支架與吊架。
6. Prohibit wooden brick fixing brackets and hangers.
感謝您的閱讀與觀看,本文的精彩內容來自:濟南電纜橋架,我們會有更多的精彩內容繼續為您呈現,詳情請點擊:http://
Thank you for your reading and watching. The wonderful content of this article comes from: Jinan Cable Bridge, we will continue to show you more wonderful content. For more details, please click: http://.
 
qq
售前咨詢熱線
15168870138
售后咨詢熱線
13465410318